Fisher & Paykel CG903MLD Manuel d'utilisateur télécharger pdf

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and speciﬁcation availability in your country, please visit our

local website listed at the end of this document or contact your local Fisher & Paykel dealer.

SAFETY AND WARNINGS

Important safety precautions!

Particular attention shall be given to the relevant requirements regarding ventilation.

Please make this information available to the person installing the appliance as it could reduce your

installation costs.

This appliance is to be installed and connected to the electricity and gas supply only by an authorised

person.

Installation must comply with your local building and local gas authority codes and electricity

regulations.

Failure to install the appliance correctly could invalidate any warranty or liability claims.

These appliances are registered in: (New Zealand) at www.ess.govt.nz and (Australia) with SAI Global

at www.saiglobal.com.

This gas appliance is suitable for connection to natural gas only. If in doubt, refer to the local gas

network operator or gas supplier to conrm gas type at installation site.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

WARNING!

Electrical shock hazard

Disconnect appliance from main power supply before continuing.

Failure to do so could result in electrical shock or death.

Before you install the appliance, please make sure that

the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance

are compatible. For adjustment conditions for this appliance, see ‘Gas rate summary’

a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to

comply with the local wiring rules and regulations. A means of disconnection with at least a 3 mm

air gap contact separation in all poles must be incorporated into the xed wiring in accordance with

the wiring rules, unless the local wiring rules allow for alternative means

the appliance is connected to a 220V - 240V 50Hz (10 A) power supply only and earthed via the

power supply cable

there is a power outlet within reach of the power supply cable (900 mm from the centre rear of the

product). This must be accessible after installation. The power supply cable should not touch any

metal parts

if the power supply cable is damaged, it is replaced only by the special cable: Part no. 531953 - Flex

Terminal Block Assy NZ/AU, obtainable from authorised Fisher & Paykel Service Agents

the supply connection point (gas shut-o valve) is accessible after installation

the benchtop is made of a heat resistant material

the installation complies with all the requirements of Australian and New Zealand Gas Installation

Standards (AS5601, NZS5261), including that the product has to be installed so that the surface

temperature of any nearby combustible surface will not exceed 65

C above ambient. See 3

‘Clearance Dimensions’.

When you install the appliance

We do not recommend you ush mount or seal this appliance into the bench with silicone or glue.

Doing so will make future servicing dicult. Fisher & Paykel will not be liable for any costs associated

with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred

by doing this.

Seal exposed bare edges of the cutout with an oil-based paint or moisture-proof polyurethane to

prevent possible moisture creeping between the cooktop trim and the benchtop.

We do not recommend the use of a down-draught extractor fan with the appliance, as it may distort

the ame pattern, causing uneven heating and reduced cooking performance.

Where this appliance is installed in marine craft or in caravans, it shall not be used as a space heater.

No combustible material or products should be placed on this appliance at any time.

Do not spray aerosols in the vicinity of this appliance while it is in operation.

If, after following the instructions given, the appliance cannot be adjusted to perform correctly,

please refer to the Service & Warranty book for warranty details and your nearest Authorised Service

Centre, Customer Care, or contact us through our website: www.sherpaykel.com.

IZONA CookSurface

Installation instructions

CG903ML & CG903MLD models

NZ AU

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - Installation instructions

Important! SAVE THESE INSTRUCTIONSThe models shown in this document may not be available in all markets and are subject to change at any time. For

Page 2 - WARNING!

PRODUCT & CABINETRY DIMENSIONS CLEARANCE DIMENSIONSProduct and cabinetry dimensions (mm)CG903ML IZONACG903MLDIZONA DEEPAoverall height of product

Page 3 - GAS RATE SUMMARY

PARTS SUPPLIEDWok stand (1)Flexiblehose (1)Blue washer (1)GAS RATE SUMMARYAll appliances are factory set for natural gas and are not currently convert

Page 4 - FLUSH MOUNTING INSTALLATION

FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED)ABCEDFHHTop viewIHIIIIProduct and cabinetry dimensions (mm)CG903MLIZONACG903MLDIZONA DEEPAoverall height

Page 5 - Important!

REMOVE FROM PACKAGING ENSURE THERE IS ADEQUATE AIR SUPPLYFIT THE ELBOW & FLEXIBLE HOSE LOWER GENTLY INTO THE CUTOUT8719 0PTFE” NPT12112AEnsure t

Page 6 - Test operation by

SECURE THE PRODUCT TO THE BENCHTOP CONNECT TO THE GAS & ELECTRICAL SUPPLYCHECK FOR GAS LEAKS TEST OPERATION1 32 4ATest operation by lighting all

Page 7 - FINAL CHECKLIST

www.sherpaykel.co.nz www.sherpaykel.com.au 599760A NZ AU 03.09FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Have you installed the clam

Commentaires sur ces manuels

Pas de commentaire

Fisher & Paykel CG903MLD Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Cuisiniers Fisher & Paykel CG903MLD. Fisher & Paykel CG903MLD User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Cuisiniers Fisher & Paykel CG903MLD