ActiveSmart™ Built-in refrigeratorRS36A80J and RS36A80U modelsUS CAINSTALLATION INSTRUCTIONS843155 B 08.15www.fisherpaykel.comFrameless cabinetry
85 PRODUCT AND CAVITY DIMENSIONSPRODUCT DIMENSIONSinches (mm)DOverall height of product* 79⁄” (2028)EOverall width of product 35⅓” (890)FMini
95 PRODUCT AND CAVITY DIMENSIONSDOOR CLEARANCE DIMENSIONS inches (mm)ADepth of door (widest opening) measured from front of cabinetry 18⁄” (48
105 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680 DOOR PANEL SETRS36A80J model shown with RD3680 door panels.CAVITY DIMENSIONS inches (mm)AOverall hei
115 PRODUCT AND CAVITY DIMENSIONS – WITH RD3684 DOOR PANEL SETRS36A80J model shown with RD3684 door panels.CAVITY DIMENSIONS inches (mm)AOverall hei
125 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680/RD3684 DOOR PANEL SET12DOOR CLEARANCE DIMENSIONS inches (mm)ADepth of door (widest opening) measured
13ACB6 CAVITY PREPARATIONSMINIMUM CAVITY DIMENSIONS inches (mm)AOverall height of cavity 80/84” (2032/2134)BOverall width of cavity 36” (914)COveral
147 CUSTOM DOOR PANEL DIMENSIONSHDABDgAEIFCgHDABDgAEIFCgRS36A80JPANEL DIMENSIONS inches (mm)AHeight of top door panel min.45⁄–max.49⁄”
157 CUSTOM DOOR PANEL DIMENSIONSThe drawings below apply to non-Water dispensing models only (RS36A80J). Dimensions are shown in Imperial (inches) a
168 80” (2032 mm) CAVITY – ATTACH ANTI-TIP BRACKETIMPORTANT!Safety requires refrigerators be stable when doors and/or drawer, are open. The anti-tip
178 84” (2134 mm) CAVITY – ATTACH ANTI-TIP BRACKETIMPORTANT!Safety requires refrigerators be stable when doors and/or drawer, are open. The anti-tip
188 84” (2134 mm) CAVITY – ATTACH TOP TRIMIMPORTANT!Take care when working with the appliance outside of the finished enclosure, as the appliance is
193 The installation aiders supplied are used to determine how far the appliance needs to be positioned into the finished enclosure, to be flush with
20!0 CONNECT TO WATER AND ELECTRICAL SUPPLYIMPORTANT!The water connection instructions below are intended only for the professional installer.DO
215 Thread the free end of the water hose into the dedicated hole located in the base of the appliance, through to the back of the appliance (refer t
22IMPORTANT!It is important that all four corners of the appliance is supported firmly onto the floor to eliminate any movement.Installing the app
23!2 TEMPORARILY FIXING YOUR PRODUCT AND ATTACHING DOOR STUDS1 Carefully open the refrigerator French doors to remove the installation aider attach
24!3 INSTALL WATER FILTER CARTRIDGE AND KICKSTRIPS2 Pull the freezer drawer out slightly and insert the filter cartridge and tool into the bottom l
25!4 ASSEMBLE DOOR PANEL SETThe assembly of Fisher & Paykel kits (EZKleen stainless steel door panels) and custom door panels are outlined below
26!5 HANGING ICE & WATER DOOR PANEL2 Angle top display tabs into the door panel. Ensure the harness is free of pinching. Firmly push against bo
27!6 HANGING NON-WATER DISPENSING DOOR PANELS1 Hang all door panels onto M8 studs and align the side bracket forks onto the refrigerator door.Ens
1FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRY1 SAFETY AND WARNINGS2 BEFORE INSTALLATION3 COMPONENTS LIST4 MAXIMUM DISTANCE OF HOSE AND
28!7 ICE AND WATER INITIATIONIce maker initiationTo initiate ice maker before use:When the appliance is first turned on after installation, the ic
291 Carefully open the refrigerator French doors to attach fixing brackets. On the LH side, place a fixing bracket over the side of the appliance and
301 Remove any remaining protective film on your door panels.2 Open the refrigerator French doors, firmly push top cover over the top studs.Repeat t
31@0 ATTACH BOTTOM KICKSTRIPFor toe kick installation higher than 4” (102 mm)1 Measure the required height for the bottom grille. On a board, caref
32@1 ATTACH SIDE TRIM BRACKETSIMPORTANT!Before installing your appliance, ensure the dimensions of the finished enclosure are correct for your appli
33@2 ATTACH SIDE TRIMSAPlasticAluminumFor 80” (2032 mm) and 84” (2134mm) cavity installations1 Place the side trim against the alcove side wall wi
34@3 ADJUSTING HINGE TENSIONING SCREWSHinge tensioning screwAHinge tensioning screws can be tightened if increased door closing force is required.1
35@4 FINAL CHECKLISTComplete and keep for safe reference:Model Serial No.Purchase Date PurchaserDealer Address Installer’s NameInstaller’s Signatur
843155 B 08.15www.fisherpaykel.comCopyright © Fisher & Paykel 2015. All rights reserved.The product specifications in this booklet apply to the s
31 SAFETY AND WARNINGS! WARNING!Electric Shock HazardRead and follow the safety and warnings outlined in this installation instructions guide before
43 COMPONENTS LISTFrench door hanging bracket(2)Drawer hanging bracket(1)Side bracket(10)Side strap(10)M5x10 pan head Phillips screw (10)Door pa
53 COMPONENTS LISTDoor handle(3)Optional accessories – The standard appliance does not include a door panel set.Fisher & Paykel door panel sets
63 COMPONENTS LISTTop kickstrip grille(1)Kickstrip filter(1)Air divider(1)Product hardware – Included with standard appliance.Screw cover(4) Bottom
74 MAXIMUM DISTANCE OF HOSE AND POWER CORDPower cord (excl. plug) – 80 ¾” (2051mm)RIGHT HAND SIDEPower cord (excl. plug) – 80 ¾” (2051mm)LEFT HAND
Commentaires sur ces manuels