Fisher & Paykel CG363MLDNGB1 Guide d'installation télécharger pdf

Important!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our

website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

SAFETY AND WARNINGS

Important safety precautions!

This appliance shall be installed in accordance with the installation requirements of the local

gas authority or the appropriate installation code or in the absence of local codes with the latest

National Fuel Gas Code ANSI Z223.1 or CAN/CSA B149.1,2 (Canada). Local building and electrical

codes must be adhered to.

Electrical installation must be in accordance with the National Electrical Code, ANSI/NFPA70 - latest

edition or CSA C22.1 (Canada) and/or local codes.

Installation in manufactured (mobile) home: installation must conform with the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile

Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable,

the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or with local codes where

applicable.

Installation in Recreational Park Trailers: installation must conform with state or other codes or, in

the absence of such codes, with the Standard for Recreational Park Trailers, ANSI A119.5.

WARNING!

Cut hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or cuts.

WARNING!

Electrical shock hazard

Disconnect product from the mains power supply before servicing. This

appliance is equipped with a three-prong grounding plug for your

protection against shock hazard and should be plugged directly into a

properly grounded power outlet. Do not under any circumstances cut or

remove the grounding prong from this plug.

Failure to follow this advice may result in electrical shock or death.

Do not remove permanently affixed labels, warnings, or plates from the product. This may void the

warranty.

Flexible appliance connectors shall meet the requirements of ANSI Z21.24 and State Boards. They

shall not exceed 36 inches (900 mm) in length. In order to avoid hazard, these appliances must be

installed according to these instructions.

This appliance must be installed by an authorized person (Warning: this appliance must be installed

by a licensed plumber or gas fitter when within the Commonwealth of Massachusetts).

Please make this information available to the person installing the appliance as it could reduce your

installation costs.

Please leave these instructions with the appliance. Inform the customer to retain for future reference

and for the local inspectors’ use.

Failure to install the appliance correctly could invalidate any warranty or liability claims.

Only genuine replacement parts may be used for servicing the appliance. These are available from

your nearest Fisher & Paykel Service Center.

Before you install the appliance, please make sure that

the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance

are compatible. For adjustment conditions for this appliance, see ‘Gas rate summary’ under step 5 .

a suitable isolating switch is incorporated in the fixed wiring in an acceptable position.

the appliance is connected to a power outlet that is electrically grounded in accordance with local

codes or in the absence of local codes, with the National Electric Code ANSI/NFPA 70 or CSA C22.2

(Canada)

there is a power outlet (110-120V 60Hz) within reach of the appliance cable (35½ ” (900 mm) from

the center rear of the appliance). This must be accessible after installation. The mains power supply

cable should not touch any metal parts

the countertop is square and level and no structural members interfere with space requirements

the countertop is made of heat-resistant material

you take note of the following recommended non-combustible materials: ¼” (6 mm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel, ⁄” (0.4 mm) stainless steel, ⁄” (0.6

mm) aluminum or ⁄” (0.5 mm) copper

the gas shut-off valve is accessible after installation

if the power supply cable is damaged, it is replaced only by the special cable: Part no. 531954 – Flex

Terminal Block Assy US, obtainable from authorized Fisher & Paykel Service Agents.

CookSurface

Installation instructions

CG363ML and CG363MLD (DEEP) models

US CA

(1,1) -1- 599648C izonaCG363cs installA2 USCA.indd 9/03/11 12:26 PM

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Installation instructions

Important! SAVE THESE INSTRUCTIONSThe models shown in this document may not be available in all markets and are subject to change at any time. For

Page 2 - WARNING!

PRODUCT & CUTOUT DIMENSIONS CLEARANCE & CABINETRY DIMENSIONSProduct and cutout dimensions (inches (mm))CG363MLCG363MLDDEEPAoverall height of p

Page 3 - PARTS SUPPLIED

IMPORTANT INSTALLATION INFORMATIONPARTS SUPPLIEDGAS RATE SUMMARY (These products are supplied factory set for NG.)*Nominal pressure with the two small

Page 4 - (NOT RECOMMENDED)

FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED)ABCEDFHHTop viewIHIIIIProduct and cabinetry dimensions (inches (mm))CG363MLCG363MLDDEEPAoverall height of

Page 5 - INSTALLATION

INSTALLATIONPTFE tape3⁄8” NPT3⁄8” NPT½” NPT20” (500 mm)2” (50 mm)12¾” - 2” (20-50 mm)112NG/LP½ “ NPTArrowx 4122”+ (50+ mm)12ACheck under the regulator

Page 6 - Test operation by

GAS ON NGpg. 8LPG1 32 4CHECK FOR GAS LEAKS AND TESTAGASONBCC4” H2O NG Test operation by lighting all burners.810BBB(1,2) -2- 599648C izonaCG363cs in

Page 7 - FINAL CHECKLIST

FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Have you installed the clamping brackets? Have you allowed for adequate air supply to the produ

Page 8

www.fisherpaykel.com www.fisherpaykel.ca 599648C US CA 04.11(2,2) -2- 599648C izonaCG363cs installA2 USCA.indd 9/03/11 12:26 PM(2,2) -2- 5996